Cci-thermal-technologies SHMK - Swivel Hanging Mounting Kit User Manual download pdf

CONTENTS

Item Qty. Description

 2 Angle Hanger

 2 Connector Hanger

 2 Adaptor Hanger

 5 Bolt, 1/2 UNC x 1-1/4

 4 Nut, 1/2 UNC

 5 Lock Washer, 1/2”

 1 Mtg Attach Assy Bracket

 1 Swivel Mtg Attach Assy

 3 Flat Washer, 1/2”

STEP 4

Screw Hanger Assemblies to

the Swivel Mtg Attach Assy

.

Swivel Hanging Mounting Kit Installation Instructions

For Heat Exchanger Unit Heaters

(En français à l’endos.)

STEP 3

Bolt Mtg Attach Assy Bracket

 to the heater using 1/2

UNC x 1-1/4 bolts, lock

washers, flat washers, and 1/2

UNC nuts.

STEP 2

Screw one Connector Hanger

 and one Adaptor Hanger

 onto each steel pipe until

tight (minimum of 5 turns

each).

Pipe cut length = Distance

from support structure to top

of heater

LESS 9-3/8” (238mm)

STEP 1

Fasten Angle Hangers  to a surface

or structure that will support the heater’s

weight using the installer supplied

fasteners. Refer to the owner’s manual

for the heater’s weight.

Installer required to supply:

a) a method of fastening the Angle Hangers  to the supporting structure that is at least as strong as four 3/8”

diameter, grade 5 bolts (see step 1) and,

b) two pieces of 1/2”, schedule 40 or heavier, steel pipe cut to suit required installation length and threaded at both

ends (see step 2).

Check that your heater model number corresponds to the model number shown on the mounting kit carton.

STEP 5

Hang assembly from Angle

Hangers ¿ using two 1/2 UNC

x 1-1/4 bolts, lock washers,

and nuts.

STEP 6

Connector Hanger  must be

hung on the inside of Angle

Hanger  as shown. Rotate

Connector Hanger  to align

with Angle Hanger  Do not

back off more than 3/4 turns.

Bolt the Swivel Mtg Attach

Assy  to the Mtg Attach

Assy Bracket  using a 1/2

UNC x 1-1/4 bolt, lock washer,

and flat washer. Swivel heater

to desired orientation and

secure in place.



 





Support

structure

















Heater

may be

rotated as

indicated

by arrows

1/2” Sch. 40, or

heavier Steel pipe







10-1/8”

(258 mm)

4-1/2”

(114 mm)

Support structure

Installer supplied

fasteners

WARNING:

If the heater is installed on a structure that is to be transported, provide additional support for the

heater during transit. The suspended weight should not exceed 300lbs (136kg). Refer to the

owner`s manual for mounting specifications and conditions.

1 2

ends (see step 2) 1

Summary of Contents

Page 1 - ends (see step 2)

CONTENTS Item Qty. Description 2 Angle Hanger 2 Connector Hanger 2 Adaptor Hanger 5 Bolt, 1/2 UNC x 1-1/4 4 Nut, 1/2 UNC 5

Page 2

LISTE DES PIÈCES Article Qté. Description 2 Cornière de suspension  2 Raccord de suspension  2 Adaptateur de suspension  5 Boulo

Cci-thermal-technologies SHMK - Swivel Hanging Mounting Kit User Manual

Browse online or download User Manual for Water boiler Cci-thermal-technologies SHMK - Swivel Hanging Mounting Kit. CCI Thermal Technologies SHMK - Swivel Hanging Mounting Kit Manuel d'utilisation

Summary of Contents

More documents for Water boiler Cci-thermal-technologies SHMK - Swivel Hanging Mounting Kit

Comments to this Manuals

Cci-thermal-technologies SHMK - Swivel Hanging Mounting Kit User Manual

Browse online or download User Manual for Water boiler Cci-thermal-technologies SHMK - Swivel Hanging Mounting Kit. CCI Thermal Technologies SHMK - Swivel Hanging Mounting Kit Manuel d'utilisation

Summary of Contents

More documents for Water boiler Cci-thermal-technologies SHMK - Swivel Hanging Mounting Kit

Comments to this Manuals

Related products and manuals for Water boiler Cci-thermal-technologies SHMK - Swivel Hanging Mounting Kit